|
HPD-763-389-3336 |
|
|
|
|
Fuel
Pump Kit
Power Maxx 416s
with 47mm carb and some race mod 400s with 39 PWKs require a fuel
pump to supply sufficient fuel flow.
Kit includes high output Mikuni pump. Pulse and fuel line, fittings, filter
and installation guide.
You will
have to change your needle & seat to
use this fuel pump.
|
|
|
|
416
Race Air Filter for 47mm Carb
Very large air
filter for use with Power Maxx Race Quad or if you have room on
your race machine.
2 3/4" inlet adaptor.
Filter cover recommended.
(see below)
|
|
|
|
Race
Filter Cover
Fits Twin Air
Part # TA152501 & TAPM47. Water repellent filter cover will
prevent water or mud from saturating your air filter. Material
is water repellent, not water proof.
|
|
|
NEW!!
High
Output Ignition Upgrade
for
400 / 416

|
High
Output Ignition Upgrade for 400 / 416
Finely
tuned, higher output replacement source coil, ignition coil,
and CDI Box. Output is 35% higher voltage and higher amperage
than original parts. Now you can gap your plug at .025" or
more without any misfiring. Because of the wider gap and higher
voltage, horsepower output WILL increase.
NOTE:
You must recheck your jetting.
Spark
Plug wire and retainer recommended
|
Ignition
Upgrade
PART # PM4IGU
LIST $290.00
|
NEW!!

|
Spark
Plug Wire and Retainer
Use this plug
wire with our high output ignition upgrade. Better insulated,
high temp cable and cap. Snap on retainer keeps plug wire from
coming off plug.
|
Spark
Plug Wire & Retainer
PART # SPW
LIST $19.00
|
|
|
New
416 Rubber Intake Manifold
NEW Rubber Intake
Manifold
New improved flow and less carburetor vibration, gives cleaner jetting
and increased horsepower. The manifold and new 47mm Power Maxx Carburetor
puts this motor over 90 horsepower. Made from a specially blended formula
of 70 durometer Acrylonitrile Butadiene Copolymer.
|
|
|
|
New
416 Piston
Lightweight
hard anadized dome, ring grooves and wrist pin hole to improve
piston life. Inlet port holes matched to 416 Power Maxx. Plus,
its 15 grams lighter than previous version.
|
|
|
|
416
Chamber
Replacement chamber
for 416 Power Maxx. 14.5 compression ratio. 205 lb cranking pressure.
Requires 110 octane fuel. Does not fit any other engines.
|
|
|
|
416
Pipe
Race pipe for
the Power Maxx 416 engine. Fits 98-03 Scrambler, 99-04 Sport/Trailblazer
400. Replacement pipe, black finish only.
|
|
|
Kevlar
Cord ATV Belt
This is the best belt available for the Sport/Scrambler/Trail Blazer ATVs. Kevlar
construction for strength and a soft compound for less belt slip.
Fits most Polaris or HPD belt drive models. Including EBS.
Does not fit 700-800 EFI Sportsmans.
Freeplay adjustment may be required.
|
PART
#HPD091
LIST $60.00
|
|
|
416
O-Ring Kit
Replacement O-Ring
Kit for 416 engine.
|
|
|
|
Twin
Air Filter
High
flow air filter increases horsepower while providing superior filtering.
Works well with stock or performance carburetor. Filter cover recommended.
|
|
|
|
Filter
Cover
Fits
Twin Air Part # TA150900
Water repellent
filter cover will prevent water or mud from saturating your air filter.
Material is water repellent, not water proof.
|
|
Aggressive
Clutch Kits
Kit
includes: Helix, weights, 2 springs, installation guide, and
shims (if needed).
Super Sport Button Kit recommended
|
416
Drag Race
Very aggressive
off the line with and throughout the power curve. Designed for Drag
Racing. (poor backshift)
|
|
416
MX Kit
Tractable power off the line. Good midrange, top and backshift. Designed
for MX or play.
|
|
|
|
Super
Duty Clutch Buttons
This
kit makes your secondary buttons almost indestructible. Used
on our super sport racers for 5 years without breakage.
|
PART
# SSBK
LIST $65.00
|
|
HPD-763-389-3336 |
|
|
|